Pneumatic And Hydraulic Equipment Page 959

R E X R O T H Mounting MT4 Table 1 - DIMENSIONS AFFECTED BY ROD DIAMETER Table 2 - DIMENSIONS NOT AFFECTED BY ROD DIAMETER Bore MM XV In. Rod V W Y RD RT Min. ZB ZJ 1.500 0.625 0.25 0.63 2.00 - 3.66 6.06 5.63 1.000 0.50 1.00 2.38 - 4.03 6.43 6.00 2.000 1.000 0.25 0.75 2.38 - 4.03 6.57 6.00 1.375 0.38 1.00 2.63 - 4.28 6.82 6.25 2.500 1.000 0.25 0.75 2.38 - 4.16 6.70 6.13 1.375 0.38 1.00 2.63 - 4.41 6.95 6.38 1.750 0.50 1.25 2.88 - 4.66 7.20 6.63 3.250 1.375 0.25 0.88 2.75 - 4.78 7.85 7.13 1.750 0.38 1.13 3.00 - 5.03 8.10 7.38 2.000 0.38 1.25 3.13 - 5.16 8.22 7.50 4.000 1.750 0.25 1.00 3.00 - 5.16 8.35 7.63 2.000 0.25 1.13 3.13 - 5.28 8.48 7.75 2.500 0.38 1.38 3.38 - 5.53 8.73 8.00 5.000 2.000 0.25 1.13 3.13 - 5.53 9.26 8.25 2.500 0.38 1.38 3.38 - 5.72 9.51 8.50 3.000 0.38 1.38 3.38 - 5.72 9.51 8.50 3.500 0.38 1.38 3.38 - 5.72 9.51 8.50 6.000 2.500 0.25 1.25 3.50 - 6.16 10.77 9.63 3.000 0.25 1.25 3.50 - 6.16 10.77 9.63 3.500 0.25 1.25 3.50 - 6.16 10.77 9.63 4.000 0.25 1.25 3.50 - 6.16 10.77 9.63 7.000 3.000 0.63 1.63 3.75 5.25 .63 6.91 12.00 10.75 3.500 0.63 1.63 3.75 5.75 .63 6.91 12.00 10.75 4.000 0.50 1.50 3.75 6.50 .75 6.91 12.00 10.75 4.500 0.50 1.50 3.75 6.50 .75 6.91 12.00 10.75 5.000 0.25 1.25 3.75 7.75 1.00 6.91 12.00 10.75 8.000 3.500 0.63 1.25 3.88 5.75 .63 7.16 13.25 11.75 4.000 0.50 1.25 3.88 6.50 .75 7.16 13.25 11.75 4.500 0.50 1.25 3.88 7.00 .75 7.16 13.25 11.75 5.000 0.25 1.25 3.88 7.25 1.00 7.16 13.25 11.75 5.500 0.25 1.25 3.88 8.25 1.00 7.16 13.25 11.75 "RT" dimension replaces "F" dimension on 7" - 8" bore sizes. All trunnion mount cylinders need a provision on both ends for pivoting. These types of cylinders are designed to carry shear loads and the trunnion and pivot pins should be carried by bearings that are rigidly held and closely fit for the entire length of the pin. Specify "XV" dimension when ordering MT4 Intermediate Fixed Trunnion mounts. If not specified, trunnion will be located at the center of the tube. The bearing retainer plate is the same as the "E" dimension for 1-1/2"-6" bore sizes and the "RD" dimension for the 7"-8" bore sizes. CDT4 MT4 Bore SAE Port In. B E EE F G J K LB P TD TL TM UM UT UW BD 1.500 1.44 2.50 -10 0.38 1.75 1.50 0.33 5.00 2.88 1.000 1.00 3.00 5.00 4.50 3.38 1.25 2.000 1.44 3.00 -10 0.63 1.75 1.50 0.44 5.25 2.88 1.375 1.38 3.50 6.25 5.75 4.13 1.50 2.500 1.69 3.50 -10 0.63 1.75 1.50 0.44 5.38 3.00 1.380 1.38 4.00 6.75 6.25 4.63 1.50 3.250 1.94 4.50 -12 0.75 2.00 1.75 0.55 6.25 3.50 1.750 1.75 5.00 8.50 8.00 5.81 2.00 4.000 2.19 5.00 -12 0.88 2.00 1.75 0.55 6.63 3.75 1.750 1.75 5.50 9.00 8.50 6.38 2.00 5.000 2.69 6.50 -12 0.88 2.00 1.75 0.77 7.13 4.25 1.750 1.75 7.00 10.50 10.00 7.75 2.00 6.000 2.94 7.50 -16 1.00 2.25 2.25 0.85 8.38 4.88 2.000 2.00 8.50 12.50 11.50 10.38 3.00 7.000 3.44 8.50 -20 - 2.75 2.75 0.95 9.50 5.38 2.500 2.50 9.75 14.75 13.50 11.50 3.00 8.000 3.44 9.50 -24 - 3.00 3.00 1.05 10.50 6.13 3.000 3.00 11.00 17.00 15.50 13.38 3.50 Rexroth Bosch JHF Catalog [ Volume 7 ] (314) 427-0600 800-444-0522 (FAX) 314-427-3502 www. j hf.com 959 Prices Subject to Change Without Notice John Henry Foster pneumatic and hydraulic equipment

Previous Page
Next Page