Pneumatic And Hydraulic Equipment Page 956

Dimensions MS3, MS7 Table 1 - DIMENSIONS AFFECTED BY ROD DIAMETER Bore MM In. Rod V W Y XS ZJ XE ZE 1.500 0.625 0.25 0.63 2.00 1.38 5.63 6.50 6.88 1.000 0.25 1.00 2.38 2.38 6.00 6.88 7.25 2.000 1.000 0.25 0.75 2.38 1.88 6.00 6.94 7.44 1.375 0.38 1.00 2.63 2.13 6.25 7.18 7.69 2.500 1.000 0.25 0.75 2.38 2.06 6.13 7.06 7.56 1.375 0.38 1.00 2.63 2.31 6.38 7.31 7.81 1.750 0.50 1.25 2.88 2.56 6.63 7.56 8.06 3.250 1.375 0.25 0.88 2.75 2.31 7.13 8.25 8.88 1.750 0.38 1.13 3.00 2.56 7.38 8.50 9.13 2.000 0.38 1.25 3.13 2.68 7.50 8.63 9.25 4.000 1.750 0.25 1.00 3.00 2.75 7.63 8.75 9.38 2.000 0.25 1.13 3.13 2.88 7.75 8.88 9.50 2.500 0.38 1.38 3.38 3.13 8.00 9.13 9.75 5.000 2.000 0.25 1.13 3.13 2.88 8.25 9.75 10.50 2.500 0.38 1.38 3.38 3.13 8.50 10.00 10.75 3.000 0.38 1.38 3.38 3.13 8.50 10.00 10.75 3.500 0.38 1.38 3.38 3.13 8.50 10.00 10.75 6.000 2.500 0.25 1.25 3.50 3.38 9.63 11.31 12.19 3.000 0.25 1.25 3.50 3.38 9.63 11.31 12.19 3.500 0.25 1.25 3.50 3.38 9.63 11.31 12.19 4.000 0.25 1.25 3.50 3.38 9.63 11.31 12.19 The side or lug mounted cylinder provides a fairly rigid mount. These type mounts can tolerate a slight amount of misalignment when the cylinder is at full stroke, but as the piston moves toward the blind end, the tolerance for misalignment decreases. It is important to note that if the cylinder is used properly, the mounting bolts are either in simple shear or tension without any compound stresses. An extended key plate option is available to eliminate the need for fitted bolts or external keys to carry the thrust load. Notes: The MS3 and MS7 mounts are only offered in 1-1/2"-6" bore sizes and have a square retainer the same size as the head. When specifiying an MS7 mount, carefully check the distance between the rod and lug to determine sufficient clearnace for the rod end attachment. It may be necessary to add extra plain rod extension to move the threaded rod end out beyond the lug. The lugs serve as nuts on the bottom two tie rods therefore making it necessary to loosen the tie rods to remove the rod bearing. CDT4 MS3 CDT4 MS7 Table 2 - DIMENSIONS NOT AFFECTED BY ROD DIAMETER Bore EB SAE Port NT SB In. E Bolt EE EL EO ET F G J K LB THD P R Bolt SE SS ST SU SW SX SY TN TS US 1.500 2.50 0.38 -10 0.88 0.38 0.81 0.38 1.75 1.50 0.33 5.00 0.38-16 2.88 1.63 0.38 6.75 3.88 0.50 0.94 0.38 0.38 0.38 0.75 3.25 4.00 2.000 3.00 0.50 -10 0.94 0.50 0.88 0.63 1.75 1.50 0.44 5.25 0.50-13 2.88 2.05 0.50 7.13 3.63 0.75 1.25 0.50 0.50 0.50 0.94 4.00 5.00 2.500 3.50 0.50 -10 0.94 0.50 0.88 0.63 1.75 1.50 0.44 5.38 0.63-11 3.00 2.55 0.75 7.25 3.38 1.00 1.56 0.69 0.69 0.69 1.31 4.88 6.25 3.250 4.50 0.62 -12 1.13 0.63 1.19 0.75 2.00 1.75 0.55 6.25 0.75-10 3.50 3.25 0.75 8.50 4.12 1.00 1.56 0.69 0.69 0.69 1.50 5.88 7.25 4.000 5.00 0.62 -12 1.13 0.63 1.13 0.88 2.00 1.75 0.55 6.63 1.00-8 3.75 3.82 1.00 8.88 4.00 1.25 2.00 0.88 0.88 0.88 2.06 6.75 8.50 5.000 6.50 0.88 -12 1.50 0.75 1.47 0.88 2.00 1.75 0.77 7.13 1.00-8 4.25 4.95 1.00 10.13 4.50 1.25 2.00 0.88 0.88 0.88 1.94 8.25 10.00 6.000 7.50 1.00 -16 1.69 0.88 1.69 1.00 2.25 2.25 0.85 8.38 1.25-7 4.88 5.73 1.25 11.75 5.13 1.50 2.50 1.13 1.13 1.13 3.31 9.75 12.00 Rexroth hydraulics (314) 427-0600 800-444-0522 (FAX) 314-427-3502 www. j hf.com JHF Catalog [ Volume 7 ] 956 Prices Subject to Change Without Notice John Henry Foster pneumatic and hydraulic equipment

Previous Page
Next Page