Pneumatic And Hydraulic Equipment Page 837

N O R G R E N ISO/VDMA CYLINDERS RA/8000,.../M Double acting (Also available single acting) Conforms to ISO 6431, VDMA 24562 and NFE 49-003-1 High performance, ruggedness and reliability Extensive range of mountings Technical data Medium: Compressed air, filtered, lubricated or non-lubricated Standard: ISO 6431, VDMA 24562, NFE 49-003-1 and corresponding BS Operation: RA/8000 double acting, adjustable cushioning RA/8000/M double acting, magnetic piston, adjustable cushioning Operating pressure: 15 to 232 psig (1 to 16 bar) 15 to 145 psig [1 to 10 bar] for 250 and 320 mm Operating temperature: -4F to +176F (-20C to +80C ) max. Consult JHF for use below +35F (+2C) Strokes: Standard, see table Non-standard strokes up to 3000 mm maximum Materials Barrel: anodised aluminum End covers: pressure diecast aluminium ( 200 to 320 mm gravity cast aluminum) Piston rod: stainless steel (Martensitic) Piston rod seals: polyurethane ( 125 to 320 mm nitrile rubber) Piston seals: polyurethane ( 125 to 320 mm nitrile rubber) 'O'-rings: nitrile rubber Options selector Note:If option is not required, disregard option position within part number eg. RA/8100/100 For combinations of cylinder variants consult our Technical Service. Piston Port Model Model Service rod size non-magnetic magnetic kit 32 12 G1/8 RA/8032/* RA/8032/M/* QA/8032/00 40 16 G1/4 RA/8040/* RA/8040/M/* QA/8040/00 50 20 G1/4 RA/8050/* RA/8050/M/* QA/8050/00 63 20 G3/8 RA/8063/* RA/8063/M/* QA/8063/00 80 25 G3/8 RA/8080/* RA/8080/M/* QA/8080/00 100 25 G1/2 RA/8100/* RA/8100/M/* QA/8100/00 125 32 G1/2 RA/8125/* RA/8125/M/* QA/8125/00 160 40 G3/4 RA/8160/* RA/8160/M/* QA/8160/00 200 40 G3/4 RA/8200/* RA/8200/M/* QA/8200/00 250 50 G1 RA/8250/* RA/8250/M/* QA/8250/00 320 63 G1 RA/8320/* RA/8320/M/* QA/8320/00 * Insert stroke length in mm. Standard models Model Plug-in cable Reed M/50/LSU/*V M/50/LSU/CP M/P73001/5 (5 m) Solid state M/50/EAP/*V M/50/EAP/CP M/P73001/5 (5 m) With integral With plug-in cable Switches *Insert cable length - 2, 5 or 10 m. Cylinder diameters (mm) Substitute 032, 040, 050, 063, 080, 100, 125, 160, 200, 250, 320 Special variants Substitute Heat resistant seals, 150C max. T Piston rod material Substitute Chrome plated stainless steel D Stainless steel R Series Substitute 8000 8 Threads Substitute Metric ports: ISO 228 (G 1/8 to G 1) A NPT ports C Variants (magnetic piston) Substitute Standard M Special wiper/seal W2 Low friction X2 Piston rod bellow MG Without cushioning MW Without cushioning, low friction X4 Double ended piston rod JM Double ended piston rod, special wiper/seal W4 Four position MT Non-rotating piston rod N2 Locking unit L4 Extended piston rod MU Extended piston rod, special wiper/seal W6 **A/8000/MU/**/***/*** /W6/ Extension (mm) Variants (non-magnetic piston) Substitute Standard None Special wiper/seal W1 Low friction X1 Piston rod bellow G Without cushioning W Without cushioning, low friction X3 Double ended piston rod J Double ended piston rod, special wiper/seal W3 Four position IT Non-rotating piston rod N1 Locking unit L2 Extended piston rod IU Extended piston rod, special wiper/seal W5 **A/8000/IU/**/***/*** /W5/ Extension (mm) # Direct acting, ## Reverse acting. Standard Stroke* Lengths (mm) 25 50 80 100 125 160 200 250 320 400 500 * Maximum stroke length is 3000 mm Non-standard stroke lengths available * DC / 8050/M * / **** norgren pneumatics JHF Catalog [ Volume 7 ] (314) 427-0600 800-444-0522 (FAX) 314-427-3502 www. j hf.com 837 Prices Subject to Change Without Notice John Henry Foster pneumatic and hydraulic equipment

Previous Page
Next Page