Pneumatic And Hydraulic Equipment Page 650

METAL PIPING SYSTEMS COMPRESSED AIR PIPING SOLUTIONS Installation That's a Snap! Infinity offers the easiest, fastest installation available. There's no welding, gluing or threading, and very little skill is needed for a professional installation. In fact, a simple pipe cutter and de-burring pipe reamer are the only tools required. For Your Piping Size Requirerments that include: 3/4" (20mm) 1" (25mm) 1-1/4" (32mm) 1-1/2" (40mm) 2" (50mm) 2-1/2" (63mm) 1 Nut: Nickel-Plated Brass 2 Seal: High Nitrile 3 Clamping Washer: Inox AISI 304 4 O-Ring Seal Made in NBR 5 Safety Ring: Technopolymeric 6 Body: Nickel-Plated Brass Flow Rates Through Piping Tube O.D. CFM mm (in.) @125 psi @150 psi @175 psi @220 psi 20mm (.75") 36 39 42 48 25mm (1") 76 81 88 99 32mm (1.25") 146 158 171 189 40mm (1.5") 266 291 310 348 50mm (2") 476 526 565 627 63mm (2.5") 881 965 1047 1153 Air Compressor to Pipe Size Selection Chart* Compressor HP Tube OD Typical Compressor mm (in.) CFM @125 psi 3 20mm (0.75") 14 5 20mm (0.75") 21 7.5 20mm (0.75") 34 10 25mm (1") 44 15 25mm (1") 66 20 32mm (1.25") 88 25 32mm (1.25") 112 30 32mm (1.25") 132 40 40mm (1.5") 168 50 40mm (1.5") 220 60 50mm (2") 258 75 50mm (2") 322 100 63mm (2.5") 425 125 63mm (2.5") 540 Installation That s a Snap! Infinity offe ers the easiest, fa no welding, gluing g or thread for a professional ins stallatio de-burring pipe reame er are For Your Piping Size Re R quirerments that include: 3/4 4" (20mm) 1" (25mm) 1-1/4" " (32mm) 1-1/2" (40mm) 2" (50mm) 2-1/2" (63mm) Flow Rate tes Through h Piping Tub be O e .D. CFM mm (in.) @12 @ 5 psi @150 psi @175 psi @220 psi 20mm (.75") 36 6 39 42 48 25mm (1" ") 76 81 88 99 32mm (1.25") 146 1 158 171 189 40mm (1.5") 266 291 310 348 50mm (2") 476 526 565 627 63mm (2.5") 881 965 1047 1153 Air Compresso or to Compressor HP 3 5 7 7.5 10 15 20 25 30 Solid Brass Nickel Plated Fittings Extruded Aluminum Tubing Vacuum to 220 psi -40 F to +1760 F Fittings can be connected and reconnected Leak free connectors Flow rates are based on a 1psi pressure drop per 100ft run of pipe and couplings in a "straight line." For loop systems, flow rates can be doubled. Example: 100ft run of 2" pipe flows 476 cfm at 125 psig with a pressure drop of 1psig. If a system is designed in a loop configuration, a flow of 952cfm with a pressure loss of 1psig per 200ft of piping and couplings can be achieved. The 1psi pressure loss will only occur if the compressor system is flowing the maximum flow capacity of the piping selected. Flows are measured at standard atmospheric conditions:14.7psi at +68F. It is vital that the size of the piping between the compressors and the connection of the loop system can flow the full capacity of the combined compressor output. * Pipe sizes indicated are only guidelines. Each compressor manufacturer states different equipment flow rates which should be checked against our selection chart. Always select a pipe size that allows for future expansion of your system. Our selection chart above allows for a minimum 15% expansion increase. 5 1 6 3 4 2 Applied System Technologies, Infinity (314) 427-0600 800-444-0522 (FAX) 314-427-3502 www. j hf.com JHF Catalog [ Volume 7 ] 650 Prices Subject to Change Without Notice John Henry Foster pneumatic and hydraulic equipment

Previous Page
Next Page