Pneumatic And Hydraulic Equipment Page 221

B I M B A How to Order The model number of Pneu-Turn Rotary Actuators consists of three alphanumeric clusters. These designate product type, series, angle of rotation and special options. Please refer to the charts below for an example of model number PT-037090-A1DV. This is a 1-1/16" bore, single rack, 90 angle of rotation actuator with angle adjustment on both sides, dual shaft and high temperature option. Option Combination Availability Due to design or compatibility restrictions, the following options may not be ordered in combination. For example, M (magnetic position sensing) and V (high temperature option) are not available in combination. * Temperature range of ball bearing option with high temperature option is 0F to +250F. ANGLE OF ROTATION 045 - 45 090 - 90 180 - 180 270 - 270 360 - 360 Rotation angles up to 1080 are available. PT-037090-A1DV SERIES - TORQUE FACTOR 006 - 9/16" Bore, Single Rack 014 - 9/16" Bore, Double Rack 017 - 3/4" Bore, Single Rack 033 - 3/4" Bore, Double Rack 037 - 1-1/16" Bore, Single Rack 074 - 1-1/16" Bore, Double Rack 098 - 1-1/2" Bore, Single Rack 196 - 1-1/2" Bore, Double Rack 247 - 2" Bore, Single Rack 494 - 2" Bore, Double Rack To determine theoretical output torque (in.- lbs.), place a decimal point between the first and second digits of the series number. Then multiply that number by the air line pressure for the approximate torque produced. For example, a PT-037-090 will produce an output torque of 0.37 times the air line pressure. OPTIONS A1 - Angle adjustment (both sides) A2 - Angle adjustment (counterclockwise rotation) A3 - Angle adjustment (clockwise rotation) B1 - Bumpers (both sides) B2 - Bumper (counterclockwise rotation) B3 - Bumper (clockwise rotation) C1 - Cushions (both sides) 1 C2 - Cushion (counterclockwise rotation) 1 C3 - Cushion (clockwise rotation) 1 D - Dual shaft E - Rear shaft (front portion of dual shaft removed; to accommodate hanging axial load) F - Hardened shaft 2 G - Polymer grease K - Square key 3 M - MRS magnetic position sensing 4 N - Low temperature option (-40F) 8 Q1 - Internal Flow Control (both sides) 9 Q2 - Internal Flow Control (counterclockwise rotation only) 9 Q3 - Internal Flow Control (clockwise rotation only) 9 R - Ball bearing 2 S - Seals - oil service 5 T - Switch track 6 V - High temperature option (0F to 400F) X - Anti-backlash (for 1-1/2" and 2" bores only) 6 1 Not available in Series 006 or 014. See below for option combination availability. 2 When ordering option -F, option -R must be ordered. -R option will include dowel pin holes. 3 006 and 014 have flat shaft. 4 Option M can be ordered with option -V, but option M's rating will change to 180. 5 Oil service not recommended for applications at pressures less than 40 psi. 1/8 NPT ports provided (orifice omitted) for 9/16" and 3/14" bores. For double rack models, oil service seals and 1/8" ports provided on bodies A and C only. 6 Option T must be ordered in conjunction with Option M. Option M can be ordered with Option-V, but Option V's rating will change to 180. 7 Option X (Anti-backlash) is available in bore sizes 1-1/2" and 2", single and double rack-up to 360 rotation. This option eliminates mid-rotational and end of rotation backlash in single rack models. It also eliminates mid-rotational backlash in double rack models. Double rack models do not have end of rotation backlash. All Pneu-Turns with this option include ball bearings Option R. Use this option to provide smooth rotation along with rotational precision. 8 Low temperature bumpers not available. 9 3/4", 1-1/16", 1-1/2", 2" bore only. A B C D E F K M R* S V X 9/16" (006) S S N/A E D,F,R,X D,E,K N/A E A,B 9/16" (014) S N/A E D,F,R,X D,E,K N/A E B 3/4" (017) S C,S B,S E D,F,R,X D,E,K N/A E A,B,C 3/4" (033) C,S B,S E D,F,R,X D,E,K N/A E B,C 1-1/16" (037) C,S B,S E D,F,R,X D,E,K N/A E B,C E,F 1-1/16" (074) C,S B,S E D,F,R,X D,E,K N/A E B,C E,F 1-1/2" (098) C,S B,S E D,F,R,X D,E,K N/A E B,C E,F 1-1/2" (196) C,S B,S E D,F,R,X D,E,K N/A E B,C E,F 2" (247) C,S B,S E D,F,R,X D,E,K N/A E B,C E,F 2" (494) C,S B,S E D,F,R,X D,E,K N/A E B,C E,F PNEU-TURN ROTARY ACTUATOR OPTIONS SERIES Bimba JHF Catalog [ Volume 7 ] (314) 427-0600 800-444-0522 (FAX) 314-427-3502 www. j hf.com 221 Prices Subject to Change Without Notice John Henry Foster pneumatic and hydraulic equipment

Previous Page
Next Page