Pneumatic And Hydraulic Equipment Page 163

Features Body - 304 Stainless Steel Heads - Anodized Aluminum Alloy Piston Rod - Ground and Polished 303 Stainless Steel Seals - Buna N (High temperature seals optional) Rod Bushing - Oil Impregnated Bronze Spring Forces - See spring force chart Pressure Rating - 200 PSI Maximum (Air only) Temperature Rating - From -20F to +150F Buna N seals with a temperature range of -20F to +150F are standard in all Bimba air cylinders. Viton seals rated for higher temperature applications are available. If cylinders are operated below 0F for extended time periods, special modifications may be required. Special seal materials are available upon request. B I M B A FLAT-1 SERIES How to Order The Model Number for all Flat-1 cylinders consists of three alphanumeric clusters. These designate type, bore size and stroke length, and mounting and special options. Please refer to the charts below for an example of Model Number FO-170.125-1V. This is a double acting, 1-1/2" bore, 1/8" stroke, pivot mount cylinder with high temperature option. FO-170.125-1V FO - Double Acting, Single End Rod FOD - Double Acting, Double End Rod FOR - Reverse Acting FOS - Single Acting TYPE BORE SIZE STROKE LENGTH OPTIONS (Enter in alphabetical order, except EE which is last) 0.125 - 1/8" 0.25 - 1/4" 0.375 - 3/8" ETC. 02 - 9/16" 31 - 2" 04 - 3/4" 50 - 2-1/2" 09 - 1-1/16" 70 - 3" 17 - 1-1/2" 125 - 4" (Enter in numeric order) MOUNTING OPTIONS No Number - Basic model (Standard counterbored mounting holes) 1 - Pivot mount 1N - Pivot mount 90 from standard 2 - Trunnion mount, both ends 1 2F - Front trunnion mount 1 2R - Rear trunnion mount 1 3 - Threaded mounting holes, both ends 3F - Threaded mounting holes, front 3R - Threaded mounting holes, rear 4 - Screw clearance holes, both ends 2 4F - Screw clearance holes, front 2 4R - Screw clearance holes, rear 2 5 - Nose Mount 3 1 Not available in 9/16" bore. 2 "Screw clearance" to allow bolt head to pass through; no counter bores. 3 Available in FO, FOR and FOS models; includes heavy-duty rear head and wiper. B - Bumpers, both ends 1 BF - Bumper, front only 1 BR - Bumper, rear only 1 CFT - Coarse female thread (fine thread standard) CMT - Male rod end (coarse thread) G - Magnalube G H - Hollow rod (double end models only) HD - Heavy duty rear head J - Failsafe operation (FOS models) 2 L - Low friction seals M, M1, M3, M4 - Magnetic position sensing 3 MT - Male rod end (fine thread) NT - Non-threaded rod P2, P3, P4 - Front port position #2, etc. 2 Q - Low temperature operation (-40F to 200F) S - Stainless steel fasteners (125 PSI maximum pressure rating - air only) T1, T3, T4 - Additional switch mounting post located in position #1, 3 or 4 V - High temperature option (0F to 400 F) W - Rod wiper (Buna N only) Y - Moly-coat (MoS 2 I. D. coating) EE0.375 - 3/8" extra rod extension, etc. EE1 - 1" extra rod extension, etc. 1 Stroke is reduced by .03" per end (.06" for option B): FOS, BR only; FOR, BF only 2 Not available in 9/16" bore 3 If magnetic position sensing is specified with option V, standard Buna-N based magnet will be provided. Magnetic position sensing is not reliable above 200 F. Approximate Power Factors (For all except F02, 3,4) 9/16" (02) = 0.25 2" (31) = 3.1 3/4" (04) = 0.4 2-1/2" (50) = 5.0 1-1/16" (09) = 0.9 3" (70) = 7.0 1-1/2" (17) = 1.7 4" (125) = 12.5 For example, a 3/4" bore model FO-041 will exert a force of approximately 0.4 times the air line pressure. Bimba JHF Catalog [ Volume 7 ] (314) 427-0600 800-444-0522 (FAX) 314-427-3502 www. j hf.com 163 Prices Subject to Change Without Notice John Henry Foster pneumatic and hydraulic equipment

Previous Page
Next Page