Pneumatic And Hydraulic Equipment Page 1208

Typical Application Hydraulic, instrumentation and chemical processing systems. Pressure Operating pressure up to 10,000 psi depending on tube and fitting size. * Vibration Good Resistance. Vibration resistance decreases with increase in tube size. Use two piece design when greater vibration resistance is required. * Temperature Range -65F to +400F at maximum operating pressures. Material Carbon Steel - AISI/SAE 12L14 Stainless Steel - Type 316 Plating - Zinc, yellow dichromate finish Used With Copper, brass, steel, aluminum and other tubing that can be flared. Advantages Zinc Plate. Choice of two or three-piece design. Broad selection of styles and sizes. Interchangeable with all sources. STEEL-SAE 37 JIC FITTINGS Tube O.D. 1/8 3/16 1/4 5/16 3/8 1/2 5/8 3/4 7/8 1 1-1/4 1-1/2 2 Thread 5/16-24 3/8-24 7/16-20 1/2-20 9/16-18 3/4-16 7/8-14 1-1/16-12 1-3/16-12 1-5/16-12 1-5/8-12 1-7/8-12 2-1/2-12 Size-B & B1 NOTE: Thread sizes B & B1 are the same. Weatherhead swivel end fittings can be used with a straight connector when space limitations will not permit full rotation of standard straight thread elbows and tees. 1. Screw connector into the O-ring boss and tighten. 2. Thread swivel nut onto connector. 3. Hold fitting in desired position and tighten swivel nut with a wrench. Adjustable Fittings Permit exact positioning of tees and elbows. Provide a leakproof joint. Eliminate distorted bosses from over tightening. 1. Lubricate O-ring by coating with a light oil or petrolatum and push back-up washer and O-ring to the extreme rear of the O-ring groove. 2. Turn the lock nut down until it just contacts the back-up washer. 3. Screw fitting by hand into straight thread boss until the back-up washer contacts the face of the boss. 4. Position the fitting by backing out (counter-clockwise) up to one full turn. Hold fitting in desired position and tighten lock nut with a wrench. 5. Assemble tube to fitting. Retighten lock nut. NOTE: O-ring, lock nuts and back-up washers are preassembled on all straight thread fittings. STRAIGHT THREAD O-RING FITTING SWIVEL FITTING (Used with Connector) Straight Thread B1 2 PIECE Thread B 3 PIECE Thread B Forged Fittings and Adapters-5000 Series Pressure Rating Chart End Size Connection Type 1/8" 3/16" 1/4" 5/16" 3/8" 1/2" 5/8" 3/4" 7/8" 1" 1-1/4" 1-1/2" 2" SAE Fittings 6000 5000 5000 5000 5000 4000 4000 4000 4000 4000 3000 3000 3000 w/Adjustable Straight Thread O-Ring 5000 5000 4500 4000 4000 4000 3000 3000 2500 2500 2000 1500 1125 With Male Pipe 6000 5000 5000 4000 4000 4000 3000 2500 2500 With Female Pipe 5000 4000 3000 2500 2000 1500 1500 1000 Brazed Fittings (TF)/SAE-5000 Series Pressure Rating Chart End Size Connection Type 1/8" 3/16" 1/4" 5/16" 3/8" 1/2" 5/8" 3/4" 7/8" 1" 1-1/4" 1-1/2" 2" SAE Fittings 5000 5000 5000 5000 5000 4500 3500 3500 3000 3000 2500 2000 1500 w/Adjustable Straight Thread O-Ring 5000 5000 4500 4000 4000 4000 3000 3000 2500 2500 2000 1500 1125 With Male or Female Pipe 5000 5000 5000 5000 4000 3000 3000 2500 2500 2000 1150 1000 1000 Weatherhead Conformance Meets specifications and standards of ASA, ASME, SAE and MS (Military Standards). How To Order To order a three-piece assembly, prefix the part number with a "3". Example: To order a male connector C5205X4 with nut and sleeve assembled, order C35205X4. To order a two-piece assembly, order nut and body separately. Example: Order male connector C5205X4 and two-piece style nut C5515X4. Bodies, nuts and sleeves can be ordered separately by part number. Stainless steel bodies, nuts and sleeves are ordered separately by part number. To order Weathercote finish (black phosphate coating) use"W" prefix in place of "C". Example: W5205X4 (special order only). To order with pipe sealants (Seal-A-Thread), add a "Z" suffix to the part number. Example: C5205X4Z (special order only). Note Weatherhead fittings with a "C" prefix are made from a forged construction. Example: C3509X2. Weatherhead fittings with a "TF" prefix are made from a brazed construction. Example: TF3509X2. Assembly Instructions 1. Cut tubing to desired length. Make sure all burrs are removed and ends are cut square. 2. Slide nut on tube. Threaded end of nut "A" must face toward fitting body. (See above.) 3. Slide sleeve on tube (3-piece assembly only). Collar end "B" of sleeve must face toward fitting body. (See above.) 4. Flare end of tubing with 37 flaring tool. a. Check flare diameter. b. Examine flare for excessive thin-out. c. On thin wall, welded or brazed tubing, use double flare to prevent pinch-off and cracked flares. 5. Lubricate threads and assemble to fitting body. Nut should be turned hand tight. 6. Tighten assembly with wrench until solid feeling is encountered. From that point, apply one-sixth turn. Label Set: FS-200 (Adhesive) Eaton Weatherhead hose and fittings (314) 427-0600 800-444-0522 (FAX) 314-427-3502 www. j hf.com JHF Catalog [ Volume 7 ] 1208 Prices Subject to Change Without Notice John Henry Foster pneumatic and hydraulic equipment

Previous Page
Next Page