Pneumatic And Hydraulic Equipment Page 1199

W E A T H E R H E A D Pipe 1/16 1/8 1/4 3/8 1/2 3/4 1 1-1/4 1-1/2 2 Size Thread 1/16-27 1/8-27 1/4-18 3/8-18 1/2-14 3/4-14 1-11-1/2 1-1/4-11-1/2 1-1/2-11-1/2 2-11-1/2 Size-B Typical Application Grease, instrumentation and most hydraulic systems. Pressure Refer to the pressure charts above. The maximum working pressure of an adapter is the lower working pressure of the end size. Ex: C3069x8x6, 8 = 4000 psi and 6 = 5000 psi. Maximum working pressure is 4000 psi. * Vibration Fair resistance. PIPE PART HEX THREAD NO. PRICE C L 1/8 C3059X2 $3.26 5/8 .15 1/4 C3059X4 $4.21 3/4 .25 3/8 C3059X6 $4.64 7/8 .25 1/2 C3059X8 $8.23 1-1/8 .25 3/4 C3059X12 $8.17 1-5/16 .25 1 C3059X16 $11.18 1-5/8 .34 SEAL-NUT FOR MALE PIPE THREADS SPECIFICATIONS FOR "SEAL NUT" Material: All Weatherhead "Seal-Nuts" are precision machined from 12L14 steel; insert is made of molded virgin Teflon . Pressure: Up to 3000 psi operating pressure. Temp. Range: Designed to operate satisfactorily from -100F to +500F. Makes every pipe connection leakproof. Permits positioning of pipe elbows and tees full 360 without overtightening. Thread seal-nut on pipe thread. Tighten pipe elbows and tees to proper position, then tighten seal nut for positive seal. Eliminates leaks on all pipe threads - Dry Seal or standard. No pipe compound required. Quick, easy installations in cramped quarters where wrench clearance is limited. "Seal-Nuts" are an economical substitute for straight thread O-ring boss fittings using original female pipe ports. "Seal-Nuts" give you positive seal on directional fittings like tees and elbows without distorting mounting bosses or damaging expensive valves and pumps. Assembly Instructions: 1. Thread Seal-Nut on to the pipe threads until 4 threads protrude beyond the teflon seal. 2. Thread fitting a minimum of 3 full threads into port. Continue turning fitting to desired position. 3. Tighten seal-nut against the port with light to medium torque to provide a positive seal. Torque required will vary with application. SEAL-NUT Teflon is a registered trademark of DuPont. STEEL PIPE FITTINGS END SIZE CONNECTION TYPE 1/8" 1/4" 3/8" 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" MALE PIPE (NPTF) 6000 5000 5000 4000 4000 4000 3000 2500 2500 FEMALE PIPE (NPTF) 5000 5000 4000 3000 2500 2000 1500 1500 1000 Forged Fittings and Adaptors Pipe Fitttings 3000 Series Pressure Rating Chart END SIZE CONNECTION TYPE 1/8" 1/4" 3/8" 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" MALE PIPE (NPTF) 5000 5000 4000 3000 2500 2000 115 0 1000 1000 FEMALE PIPE (NPTF) 5000 5000 4000 3000 2500 2000 1150 1000 1000 Brazed Fittings (TF) Pipe Fitttings 3000 Series Pressure Rating Chart * Temperature Range -65F to +400F. Material Carbon Steel - AISI/SAE 12L14 Stainless Steel - type 316 Plating - Zinc, yellow dichromate finish ASTM B633 Type II. Used With Brass, bronze and iron pipe. Advantages Dryseal pipe threads (NPTF) (SAE J476), zinc plate, compact size. Broad range of sizes and styles. Assembly Instructions 1. Tighten approximately 2-1/2 turns past hand tight. 2. Welding procedure: Use electric weldrod AWS-E7018. Recommended procedure specifies using lower amperage than usual and puddling of molten metal to permit gasses created by lead in steel to work through molten lead deposit. Label Set: FS-2000 (adhesive) Weatherhead Eaton Weatherhead hose and fittings JHF Catalog [ Volume 7 ] (314) 427-0600 800-444-0522 (FAX) 314-427-3502 www. j hf.com 1199 Prices Subject to Change Without Notice John Henry Foster pneumatic and hydraulic equipment

Previous Page
Next Page