Pneumatic And Hydraulic Equipment Page 1143

GOLD SEAL ROTARY VANE ACTUATOR Pneumatic Inlets . . . . . . . . . . . . . . . . . . . . . . . . .1/4" FNPT Minimum Pressure . . . . . . . . . . . . . . . . . . 35psi Maximum Pressure . . . . . . . . . . . 200 to 500psi Cycle Rates Max non-lubed rate: Double Vane . . . . . . . . . . . . . . . . . . 40 cpm Single Vane . . . . . . . . . . . . . . . . . . 20 cpm Max lubed rate: Double Vane . . . . . . . . . . . . . . . . . 300 cpm Single Vane . . . . . . . . . . . . . . . . . 200 cpm Shaft Load Capacities Maximum Side Load . . . . . . . . . . . . . . . 500 lbs Maximum End Load . . . . . . . . . . . . . . . . . 25 lbs Temperature Range -20 F to 180 F Rotary Motion Max Backlash All Models . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 Materials Seals: Stator & Rotor . . . . . . . . . . . . . . . Urethane Shaft & Cylinder . . . . . . . . . . . . . . . . .Buna Cylinder . . . . . . . . . . . . . . . . . . . . anod alum End caps . . . . . . . . . . . . . . . . Cast anod alum Bearings . . . . . . . . . . . . . . . . . . . . . . . needle Hydraulic Service Use of a paraffin based hydraulic oil is recommended. DO NOT USE Skydrol, Brake Fluid, water based fluids, or F type automatic transmission fluid. Filtration Air . . . . . . . . . . . . . . . . . . . . . . . . . 25-50 microns Hydraulic . . . . . . . . . . . . . . . . . . . . 10-25 microns Leak Rates Air . . . . . . . . . . . . . . . . .Less than 4 cfh @ 100 psi Hydraulic . . . . . . . . . . . . . . . . . .0.5 cim @ 500 psi Rotation Tolerance 45 is nominal, 45 4 0 actual 90 is nominal rotation, 94 actual 180 is nominal 180 4 0 actual (except hardened shaft) 270 is nominal rotation, 274 actual 2 Fatigue Proof & Stainless Steel Shaft 5 Hardened Steel Shaft Standard Rotations TORQUE CHARTS SINGLE VANE 180 & 270 DOUBLE VANE 45 & 90 psi Actuator Model in.-lbs. Turn-Act 1 440 500 2 875 Turn-Act 1 350 400 2 700 Turn-Act 1 265 300 2 525 Turn-Act 1 220 250 2 440 Turn-Act 1 175 200 2 350 3 700 Turn-Act 1 135 150 2 265 3 525 Turn-Act 1 110 125 2 220 3 440 Turn-Act 1 87 100 2 175 3 350 Turn-Act 1 70 80 2 140 3 280 Turn-Act 1 55 60 2 105 3 210 Turn-Act 1 35 40 2 70 3 140 psi Actuator Model in.-lbs. Turn-Act 1 875 500 2 1750 Turn-Act 1 700 400 2 1400 Turn-Act 1 525 300 2 1050 Turn-Act 1 440 250 2 875 Turn-Act 1 350 200 2 700 3 1400 Turn-Act 1 235 150 2 525 3 1050 Turn-Act 1 220 125 2 440 3 875 Turn-Act 1 175 100 2 350 3 700 Turn-Act 1 140 80 2 280 3 560 Turn-Act 1 105 60 2 210 3 420 Turn-Act 1 70 40 2 140 3 280 How to Order: Turn-Act (TA) END UNIT OPTIONS OPTIONS MODEL CAPS SHAFT MATERIAL 113 - 3 W 2 - XXX - XXX 1 2 3 4 5 3 Shaft To Specify other modifications; Consult Factory Y Single End-No Keyway M Double End-No Keyway Each End W Single End-Woodruff Key V Double End-Woodruff Key Each End U Single End-Shaft Flat T Double End-Shaft Flat Each End S Single End-Keyway R Double End-Keyway Each End 4 Unit Materials Shaft-Body-Trim 1 1144 Carbon Steel-Anodized Aluminum-Carbon Steel 2 Hardened Carbon Steel-Anodized Aluminum-Carbon Steel 3 303 Stainless Steel-Anodized Aluminum-Stainless Steel 4 303 Stainless Steel-303 Stainless Steel-Stainless Steel 5 Hardened 440 SS Steel-Anodized Aluminum-Stainless Steel 6 316 Stainless Steel-316 Stainless Steel-Stainless Steel 5 Options Additional options available. 000 No Options 100 Flange Mount-Rod End 101 Flange Mount-Cap End 200 Side Angle Mounting Brackets-Mounting Surface 3 & 7 300 Extended Tie Rods-Rod End 301 Extended Tie Rods-Cap End 320 Extended Tie Rods-Both Ends 400 Adjustable Stroke Control-Cap End, Position 5 401 Adjustable Stroke Control-Rod End, Position 1 500 Electrical Position Indicator-Cap End, Position 5 704 Teflon Impregnated Hard Anodized 801 Side Mounts-Positions 2 & 6 803 Side Mounts-Positions 4 & 8 804 Side Mounts-Positions 2, 4, 6 & 8 900 Thrust Protection-Cap End, Position 1 901 Thrust Protection-Rod End, Position 1 B00 Urethane Bumpers T01 3/8" Trantorque Shaft Coupler-Carbon Steel T02 3/8" Trantorque Shaft Coupler-Stainless Steel Stainless Shaft Coupler has 1/3 the transmissible torque as T01 Switch Options Additional switch options available. All Axx Switch Options are Single End Only A00 Switch Package-No Switches A02 Switch Package-2 Reed Switches A05 Switch Package-2 Sourcing Switches A08 Switch Package-2 Sinking Switches Double end options available. 2 End Caps To Specify other modifications; Consult Factory 1 Pneumatic 2 Pneumatic-Low Profile 3 Pneumatic-with Drain Ports 4 Pneumatic-with Vacuum Ports 1 Model Model Series - Torque - Rotation 111 TA - 87 - 270 112 TA - 175 - 90 113 TA - 87 - 180 114 TA - 175 - 45 121 TA - 175 - 270 122 TA - 350 - 90 123 TA - 175 - 180 124 TA - 350 - 45 131 TA - 350 - 270 132 TA - 700 - 90 133 TA - 350 - 180 134 TA - 700 - 45 141* TA - 500 - 270 142* TA - 1000 - 90 143* TA - 500 - 180 144* TA - 1000 - 45 *These models require '2' or '5' for the selection in block #4 "Unit Materials". T U R N A C T Turn Act Turn-Act JHF Catalog [ Volume 7 ] (314) 427-0600 800-444-0522 (FAX) 314-427-3502 www. j hf.com 1143 Prices Subject to Change Without Notice John Henry Foster pneumatic and hydraulic equipment

Previous Page
Next Page