Pneumatic And Hydraulic Equipment Page 1080

IMPORTANT Style 3 Rod End is standard and will be furnished unless otherwise specified. Alternate Rod End Styles 1, 2, 4 and 6 are available at no extra cost. Special rod end configurations are available for a nominal extra charge. A wide selection of rod end accessories is shown in separate Accessories Section. ALTERNATE - STYLE 1 Plain male Rod End with no threads. Used for pushing, holding knockouts, etc. MM ROD DIA. C 20 1 + 1 /16 8 - 0 ALTERNATE - STYLE 4 Female thread, used with male accessories for shorter over-all cylinder length. D WRENCH FLATS KJ THREAD KL C ALTERNATE - STYLE 2 Male thread with adequate shoulder for locking accessory. D WRENCH FLATS MM ROD DIA. KK THREAD C A STANDARD - STYLE 3 Male thread same diameter as Piston Rod. No shoulder for locking accessories. D WRENCH FLATS CC THREAD MM ROD DIA. C A ALTERNATE - STYLE 6 Used with S.A.F.E. accessory (see separate Accessories Section) for fast, close radial alignment. MM ROD DIA. AF DIA. AE AD AC 4 1 8 5 3 2 7 6 PORT POSITIONS HEAD, CAP AND TRUNNION CONFIGURATIONS BORE SIZES 1-1/2", 2", 2-1/2", 3" AND 3-1/2" ALL MOUNTS. ALSO 4" AND 5" OF CLEVIS MOUNT 4 1 8 5 6 7 2 3 BORE SIZES 4" AND 5" ALL MOUNTS EXCEPT CLEVIS 1 2 3 4 8 7 6 BORE SIZES 6", 7" 8" AND 10" ALL MOUNTS 5 Alternate port positions, are those that can be accomplished by rotating the head and/or the cap. There is no extra charge for these positions but they must be specified on your order. Alternate and Optional positions available are indicated in the charts above. Optional port positions are those that can be accomplished by drilling and tapping auxiliary bosses on the castings. Since heads and caps in stock are already ported in the standard positions, the standard parts must be plugged. There is a small additional charge for plugging and re-porting. In cases of large quantity orders, a special run of castings can be machined with ports in the desired optional positions. Optional positions must be specified on your orders. ALTERNATE PORT POSITIONS INTER- FRONT REAR MEDIATE CLEVIS FOOT FLANGE FLANGE TRUNNION MOUNT MOUNT HEAD CAP HEAD CAP HEAD CAP HEAD CAP HEAD CAP 2, 3, 4 7 - 3 6, 7, 8 2, 3, 4 7 2, 3, 4 6, 7, 8 OPTIONAL PORT POSITIONS INTER- FRONT REAR MEDIATE CLEVIS FOOT FLANGE FLANGE TRUNNION MOUNT MOUNT MOUNT MOUNT MOUNT HEAD CAP HEAD CAP HEAD CAP HEAD CAP HEAD CAP - 6, 8 2, 4 6, 8 2, 4 - - 6, 8 - - Standard port positions are 1 and 5. Unless otherwise specified, ports will be supplied in those positions. FLANGE MOUNT BF UF E TM TB INTERMEDIATE TRUNNION MOUNT BORE SIZES 1-1/2", 2", 2-1/2", 3", 3-1/2", 4" AND 5" In bore sizes 1-1/2", 2", 2-1/2", 3" and 3-1/2", all mounts have square heads, caps and trunnions with four tie rods as pictured on Pages C20-4 and C20-5. This is also the case with the 4" and 5" bore sizes of the Clevis Mount. In bore sizes of 4" and 5", all mounts except clevis have hexagon heads with six tie rods as shown below. The intermediate trunnion in 4" and 5" bore sizes is round with milled flats for the trunnion pins. BORE SIZES 6", 7", 8" AND 10" In bore sizes 6", 7", 8" and 10", all mounts have octagon heads and caps with eight tie rods as shown in below. The intermediate trunnion is round with milled flats for the trunnion pins. UL FOOT MOUNT EA INTERMEDIATE TRUNNION MOUNT TM E TB CLEVIS MOUNT E FOOT MOUNT EA UL FLAGE MOUNT BF UF ROD END DIMENSIONS MM ROD BORE DIA. A AC AD AE AF C CC D KJ KK KL 1-1/2 1/2 1 1/2 3/16 5/16 1/2 1/2-20 7/16 5/16-24 3/8-24 5/8 2 1/2 1 1/2 3/16 5/16 1/2 1/2-20 7/16 5/16-24 3/8-24 5/8 2-1/2 5/8 1 1-1/8 5/8 1/4 3/8 1/2 5/8-18 1/2 7/16-20 1/2-20 7/8 3 3/4 1-1/8 1-1/4 11/16 5/16 7/16 1/2 3/4-16 5/8 1/2-20 5/8-18 7/8 3-1/2 3/4 1-1/8 1-1/4 11/16 5/16 7/16 1/2 3/4-16 5/8 1/2-20 5/8-18 7/8 4 1 1-1/2 15/16 3/8 11/16 1/2 1-14 7/8 3/4-16 3/4-16 1 5 1 1-1/2 15/16 3/8 11/16 1/2 1-14 7/8 3/4-16 3/4-16 1 6 1 1-1/2 15/16 3/8 11/16 1/2 1-14 7/8 3/4-16 3/4-16 1 7 1-3/8 2 1-3/4 1-1/16 3/8 7/8 5/8 1-1/4-12 1-1/8 7/8-14 1-14 11/2 8 1-3/8 2 1-3/4 1-1/16 3/8 7/8 5/8 1-3/8-12 1-1/8 1-14 11/2 10 1-3/4 2 - 3/4 1-1/2-12 1-1/2 - 1-1/4-12 - C20 SERIES-ROD ENDS AND PORTING Sheffer cylinders (314) 427-0600 800-444-0522 (FAX) 314-427-3502 www. j hf.com JHF Catalog [ Volume 7 ] 1080 Prices Subject to Change Without Notice John Henry Foster pneumatic and hydraulic equipment

Previous Page
Next Page