Pneumatic And Hydraulic Equipment Page 1066

A SERIES-CLEVIS AND TRUNNION MOUNTING DIMENSIONS 7" THRU 14" BORES BORE 7 8 10 12 14 CB 1-1/2 2 2-1/2 CD 1 1-3/8 1-3/4 2 CL 3 4 5 CW 3/4 1 1-1/4 E 7-1/2 8-1/2 10-5/8 12-3/4 14-3/4 EE NPTF 3/4 1 1-1/4 G 1-7/8 2-1/8 2-3/16 2-7/8 J 1-3/8 1-7/8 1-15/16 2-3/8 K 9/16 5/8 3/4 L 1-1/2 2-1/8 2-1/4 2-1/2 LR 1 1-3/8 1-3/4 2 MM 1-3/8 1-3/4 2 2-1/2 MR 1 1-3/8 1-3/4 2 RS 4 TA 4-1/4 4-3/4 5-7/8 6-7/8 8 TB 8-1/2 9-1/2 11-3/4 13-3/4 16 TD 1-3/8 1-3/4 2 TL 1-3/8 1-3/4 2 TM 8-3/4 9-3/4 12 14 16-1/4 TT 2-1/2 3 3-1/2 UM 11-1/2 12-1/2 15-1/2 17-1/2 20-1/4 UT 10-1/4 11-1/4 14-1/8 16-1/4 18-3/4 THESE DIMENSIONS** AFFECTED BY ROD SIZE BORE 7 8 10 12 14 XG 2-13/16 3-1/8 3-1/4 3-13/16 Y 2-13/16 3-1/8 3-1/4 3-13/16 THESE DIMENSIONS** AFFECTED BY ROD SIZE AND STROKE BORE 7 8 10 12 14 XC 8-1/4 10-3/8 11-1/8 12-7/8 XI(MIN) 4-3/4 5-1/2 5-11/16 6-5/8 XI(MAX)* 4-1/8 4-7/8 5-7/16 6-1/2 XJ 6-1/16 7-1/4 7-7/8 9-5/16 ZB 7-5/16 8-7/8 9-1/2 11-1/8 ZC 9-1/4 11-3/4 12-7/8 14-7/8 THESE DIMENSIONS AFFECTED BY STROKE BORE 7 8 10 12 14 LB 5-1/8 6-3/8 6-7/8 8-1/8 P 3-1/4 4-1/8 4-5/8 5-1/2 These dimensions are for standard rod only. *+ Stroke **Dimensions shown are for standard rod size only. For oversize and 2:1 rods, add N dimension shown on rod end chart. MOUNTING INFORMATION Clevis Mount Cylinders are furnished with a hard chrome plate clevis pin and retainers. For a complete line of accessories (rod eyes, rod clevises, clevis and pivot mounting brackets, jam nuts and pin) designed for use with Sheffer cylinders, see separate Accessories Section . All Clevis and Trunnion Cylinders need provision on both ends for pivoting in one direction. Alignment in the other direction is essential in order to avoid excessive side loading. Where two-direction pivoting is necessary, contact our Distributor for specific recommendations. Trunnion Pins on trunnion mount cylinders are designed for shear loads only, not bending loads. Customer trunnion pin pillow blocks should be rigid and mounted as close to the head as possible. Bearing should be provided for the full length of the trunnion pin. Lubrication should be provided to the pins. Trunnion pins are an integral part of the ring on the intermediate trunnion mount. Mounting position (Dimension XI) of the intermediate trunnion must be given on order. Sheffer cylinders (314) 427-0600 800-444-0522 (FAX) 314-427-3502 www. j hf.com JHF Catalog [ Volume 7 ] 1066 Prices Subject to Change Without Notice John Henry Foster pneumatic and hydraulic equipment

Previous Page
Next Page