Pneumatic And Hydraulic Equipment Page 1026

FRONT FLANGE DIMENSIONS EE BORE E NPT SAE FB** FF G J K LB* P* R TF UF 1-1/8 1-3/4 1/4 -6 1/4 1/2 1-1/8 1 1/4 3-1/4* 2-3/16* 1.19 2-3/8 3 1-1/2 2-1/2 1/2 -10 3/8 1-3/4 1-1/2 5/16 4-5/8* 2-7/8* 1.63 3-7/16 4-1/4 2 3 1/2 -10 1/2 5/8 1-3/4 1-1/2 7/16 4-5/8* 2-7/8* 2.05 4-1/8 5-1/8 2-1/2 3-1/2 1/2 -10 1/2 5/8 1-3/4 1-1/2 7/16 4-3/4* 3* 2.55 4-5/8 5-5/8 3-1/4 4-1/2 3/4 -12 5/8 3/4 2 1-3/4 9/16 5-1/2* 3-1/2* 3.25 5-7/8 7-1/8 4 5 3/4 -12 5/8 7/8 2 1-3/4 9/16 5-3/4* 3-3/4* 3.82 6-3/8 7-5/8 5 6-1/2 3/4 -12 7/8 2 1-3/4 3/4 6-1/4* 4-1/4* 4.95 8-3/16 9-3/4 6 7-1/2 1 -16 1 2-3/8 2-3/8 7/8 7-3/8* 4-7/8* 5.73 9-7/16 11-1/4 7 8-1/2 1-1/4 -20 1-1/8 1 2-7/8 2-7/8 1-3/16 8-1/2* 5-3/8* 6.58 10-5/8 12-5/8 8 9-1/2 1-1/2 -24 1-1/4 1 3-1/4 3-1/4 1-1/4 9-1/2* 6-1/8* 7.50 11-13/16 14 10 12-5/8 2 -32 1-3/4 1-11/16 3-7/8 3-7/8 1-11/16 12-1/8* 8* 9.62 15-7/8 19 12 14-7/8 2-1/2 -32 2 1-15/16 4-7/8 4-7/8 1-15/16 14-1/2* 9-3/8* 11.45 18-1/2 22 14 17-1/4 2-1/2 -32 2-1/4 2-7/16 5-3/8 5-3/8 2-5/32 17* 10-3/4* 13.34 21-1/8 25-1/4 *Be sure to add stroke to this dimension. **Clearance holes for indicated bolt size. Alternate port at no extra charge. SAE port is standard. MM ROD BORE DIA. FA RD VB W WF WG Y ZB* 1-1/8 5/8 STD. - - - 5/8 1-1/8 2-1/4 1-23/32 4-5/8* 5/8 STD. - - - 5/8 1 2-3/4 2 5-15/16* 1 2:1 - - - 1 1-3/8 3-1/8 2-3/8 6-5/16* 1 STD. 11/32 2.375 7/8 3/4 1-3/8 3-1/8 2-3/8 6-7/16* 1-3/8 2:1 19/32 2.875 1 1 1-5/8 3-3/8 2-5/8 6-11/16* 1 STD. 11/32 2.375 7/8 3/4 1-3/8 3-1/8 2-3/8 6-9/16* 1-3/8 19/32 2.875 1 1 1-5/8 3-3/8 2-5/8 6-13/16* 1-3/4 2:1 - - - 1-1/4 1-7/8 3-5/8 2-7/8 7-1/16* 1-3/8 STD. 19/32 2.875 1 7/8 1-5/8 3-5/8 2-3/4 7-11/16* 1-3/4 19/32 3.250 1-1/8 1-1/8 1-7/8 3-7/8 3 7-15/16* 2 2:1 - - - 1-1/4 2 4 3-1/8 8-1/16* 1-3/4 STD. 19/32 3.250 1-1/8 1 1-7/8 3-7/8 3 8-3/16* 2 19/32 3.562 1-1/8 1-1/8 2 4 3-1/8 8-5/16* 2-1/2 2:1 19/32 4.000 1-1/4 1-3/8 2-1/4 4-1/4 3-3/8 8-9/16* 2 STD. 19/32 3.562 1-1/8 1-1/8 2 4 3-1/8 9* 2-1/2 19/32 4.000 1-1/4 1-3/8 2-1/4 4-1/4 3-3/8 9-1/4* 3 19/32 4.750 1-1/4 1-3/8 2-1/4 4-1/4 3-3/8 9-1/4* 3-1/2 2:1 23/32 5.187 1-1/4 1-3/8 2-1/4 4-1/4 3-3/8 9-1/4* 2-1/2 19/32 4.000 1-1/4 1-1/4 2-1/4 4-5/8 3-1/2 10-1/2* 3 19/32 4.750 1-1/4 1-1/4 2-1/4 4-5/8 3-1/2 10-1/2* 3-1/2 23/32 5.187 1-1/4 1-1/4 2-1/4 4-5/8 3-1/2 10-1/2* 4 2:1 23/32 5.750 1-1/4 1-1/4 2-1/4 4-5/8 3-1/2 10-1/2* 3 STD. 19/32 4.750 1-1/4 1-1/4 2-1/4 5-1/8 3-13/16 11-15/16* 3-1/2 23/32 5.187 1-1/4 1-1/4 2-1/4 5-1/8 3-13/16 11-15/16* 4 23/32 5.750 1-1/4 1-1/4 2-1/4 5-1/8 3-13/16 11-15/16* 4-1/2 3/4 6.250 1-1/4 1-1/4 2-1/4 5-1/8 3-13/16 11-15/16* 5 2:1 3/4 6.750 1-1/4 1-1/4 2-1/4 5-1/8 3-13/16 11-15/16* 3-1/2 23/32 5.187 1-1/4 1-1/4 2-1/4 5-1/2 3-15/16 13* 4 23/32 5.750 1-1/4 1-1/4 2-1/4 5-1/2 3-15/16 13* 4-1/2 3/4 6.250 1-1/4 1-1/4 2-1/4 5-1/2 3-15/16 13* 5 3/4 6.750 1-1/4 1-1/4 2-1/4 5-1/2 3-15/16 13* 5-1/2 2:1 3/4 7.250 1-1/4 1-1/4 2-1/4 5-1/2 3-15/16 13* 4-1/2 STD. 1-5/8 6.250 1-15/16 1-1/4 2-15/16 6-13/16 5 16-3/4* 5 1-5/8 6.750 2-3/16 1-1/2 3-3/16 7-1/16 5-1/4 17* 5-1/2 1-5/8 7.250 2-3/16 1-1/2 3-3/16 7-1/16 5-1/4 17* 7 2:1 1-5/8 9.750 2-3/16 2 3-11/16 7-9/16 5-3/4 17-1/2* 5-1/2 STD. 1-5/8 7.250 2-3/16 1-1/4 3-3/16 8-1/16 5-3/4 19-5/8* 7 1-5/8 9.75 2-3/16 1-7/8 3-13/16 8-11/16 6-3/8 20-1/4* 8 2:1 1-7/8 10.875 2-7/16 2-7/16 4-3/8 9-1/4 6-15/16 20-13/16* 7 STD. 2-3/8 9.75 2-13/16 1-7/8 4-5/16 9-11/16 7-7/16 23-15/32* 10 2:1 2-3/8 13.73 2-15/16 2-1/2 4-15/16 10-5/16 8-1/16 24-3/32* *Be sure to add stroke to this dimension. 14 12 10 8 7 6 5 4 3 1 / 4 2 1 / 2 1 / 2 HH SERIES-FRONT FLANGE MOUNTING DIMENSIONS GOOD - FRONT FLANGE MOUNT While this style of mount is a widely used one, its use should be restricted to pressures under 1000 psi, short strokes (under 36") and standard rod diameters. Note that the Front Head Flange mount has the same mounting hole pattern. BETTER - FRONT FLANGE EXTRA MOUNT Satisfactory for maximum operating pressure and long strokes if properly applied. See separate Accessories Section for detailed mounting data and separate Engineering Section for long stroke information. BEST - FRONT HEAD FLANGE MOUNT Highly recommended. This is the best style of flange mounting. With this style, the cyl- inder can be mounted on the back face of the Head Flange if desired. This mounting style is used extensively on high tonnage presses and other heavy duty applications. To dimensionally interchange with the FF mount, see separate Accessories Section for Front Head Flange Spacer Bars. We highly recommend that consideration be given to the use of a Style 6 rod end and S.A.F.E. Coupling (see separate Accessories Section) to achieve good radial alignment. Selection of piston rod diameter can be determined by consulting the separate Engineering Section. CAUTION See separate Accessories Section for information concerning the application of Flange Mount Cylinders. Sheffer cylinders (314) 427-0600 800-444-0522 (FAX) 314-427-3502 www. j hf.com JHF Catalog [ Volume 7 ] 1026 Prices Subject to Change Without Notice John Henry Foster pneumatic and hydraulic equipment

Previous Page
Next Page